MR380-0

MR380-0 1E OEM Controller

MR380-0 1E OEM Controller

MR38X-0 Series OEM Controller

The MR380-0-1E OEM Controller is a low-cost, small form factor PCB designed to be embedded into the user’s product or system. This controller is a Short Haul 850nm multimode solution for use with any MR38X ZapFREE® Fiber Optic Signaling Sensor.

Specifications

Functional States Example: MR386 Series Fiber Optic Microswitch
For Normally Open (NO) Sensors
(Light interrupted)		 Logic Output=LO, Logic Output=0V
Open Collector Output =OFF
For Normally Closed (NC) Sensors
(Light throughput)		 Logic Output=HI, Logic Output>4.5V
Open Collector Output=ON
Electrical Interface NOTE: Electrical connections shall not exceed 3 meters.
Connector CamdenBoss P/N CTB1301/6A (one included with Controller)
6C, Screw-Type Terminal Plug, 5mm contact spacing, 1.5mm cable entry
Logic Output High=4.5V min (2k Ω Load), Low=0.25V max
Open Collector Output Maximum Load Voltage=24 VDC
Maximum Current 180mA, Protected by resetable fuse
Power Supply +5V to +24V DC Maximum
Current Consumption=8mA max at 5V DC, 12 mA at +24V DC and R8 Installed
Optical Interface
Operating Wavelength 850nm, VCSEL
System Loss Budget 15 dB
Maximum Distance Up to 1500 meters
Fiber Types 62.5/125μm 0.275NA OM1 Multimode Fiber
50/125μm 0.22NA OM2/OM3 Multimode Fiber
Explosive Atmospheres Inherently Safe, Optical Radiation
EX Classification Controller shall be installed in non-hazardous location only
Power supply to Controller shall be current limited to 200mA or less
IECEx Test Report GB/CML/ExTR 16.0105.00/00
ATEX [EPL Mb/Gb/Gc/Db/Dc]
EAEU/GOST [EPL Mb/Gb/Gc/Db/Dc]
IEC Ex [EPL Mb/Gb/Gc/Db/Dc]
North America Controller shall be installed in non-hazardous area only
Environmental Performance
Temperature/Humidity -40°C to +70°C (-40°F to +158°F), 0-85% RH, Non-Condensing
Ingress Protection IP00 (none)
Physical Attributes
Mounting 4x #2-56 or M2.5 screws, Mounting Pattern=1.60 x 2.60 inches
Housing 5.08 x 7.62 cm (2.00 x 3.00 inches)
Weight 25 g (1 oz)

Specifications subject to change without notice

 

Features

  • Low cost, PCB form factor
  • For use with either 50/125 OM2/OM3 or 62.6/125 OM1 multimode fiber
  • Controller’s inherently safe, optical radiation is approved for EPL Mb/Gb/Gc/Db/Dc applications
  • For increased safety, the controller is designed to default to the emergency state when: (1) switch is depressed, (2) in case of broken fiber, (3) in case of a fiber being disconnected, or (4) loss of power.

Interfaces

  • Digital logic output
  • Open-Collector output for controlling an external relay

Downloads

Manual
Datasheet
Drawing
CAD Files
Declaration Of Conformity

TO ORDER

Call +61 (0) 7 5533 5367 or email info@qualityincontrol.com.au

Ordering Information

MR380-0-1E OEM Multimode E-Stop/Switch Controller Board

Quick Ship Configurations

MR380-0-1E OEM Multimode E-Stop/Switch Controller Board
50-CTB13016A/6A Replacement Part, CamdenBoss Terminal Plug
MR387-2S-03 E-Stop, 30mm Button, 62.5/125 MMF Pigtail, Interface=Duplex LC, Length=3m
MR387-2S-D00 E-Stop in IP Housing, 30mm Button, For 62.5/125 MMF Link, Interface=ODVA IP-LC Receptacle

Related products